Airaid MXP Cold Air Intake System Installation - 2016 Ford Explorer- Video
Hey guys, it's Jake here with the etrailer. today we have a 2016 Ford Explorer, and we're going to be doing a replacement air filter by Airways. Now this replacement air filter is going to be quite a bit larger than your factory air filter. A lot of people know them as cool air intakes, and that's exactly what it's designed to do. It's designed to take a high volume of air to condense it down and to cool it when it goes into your engine, therefore your engine is going to perform better. You're going to get better gas mileage, a little bit more torque, and a little bit more horsepower out of it. more
1/13/2020 4:12:07 PM
Airaid CAD Cold Air Intake System Installation - 2007 Chevrolet Corvette- Video
Speaker 1: Today on this 2007 Chevrolet Corvette, we will be having a look at and showing you how to install the Airraid CAD Cold Air Intake System with a SynthaMax Dry Filter. Available with a black filter as part number AR252-218, a blue filter as part number AR253-218 and a red filter as part number AR251-218.Here's what our air intake system looks like installed. Now the reason you're going to want an air intake system such as this, is if you own a performance vehicle like this Corvette here, this will help you gain even more performance.This open cold air intake design will help draw in more colder, dense air into your engine helping improve horsepower, torque and performance. The air filter is a dry, washable filter, so you don't ever have to worry about replacing your air filter again. When it's dirty, you can simply wash it off, let it dry and put it back on and you're ready to get back on the road. It offers 99.6% filtration efficiency, so it will protect your engine while still increasing air flow.With this system installed, you may notice the increased power with your acceleration. more
4/9/2018 4:07:12 PM
aFe Direct-Fit Cold Air Intake System Installation - 2013 GMC Sierra- Video
Speaker 1: Today on our 2013 GMC Sierra 2500, we'll be having a look at and installing the aFe Direct-Fit Cold Air Intake System with Pro Dry S Filter, part number: AFE51-12322. Also available with a Pro Guard 7 Oiled Filter as part number: AFE75-12322. Here's what our air intake system looks like installed. This filter combined with the system has 33% more air flow than the factory air intake system. This filter also offers us a 99.2% filtration efficiency rate, and it is a lifetime filter, it is oil-free, you don't ever have to worry about replacing it. When it's dirty, you can simply wash it off, let it dry, and stick it back inside your vehicle and you're good to go.Now, this filter will save you money in the long run because you don't ever have to worry about replacing the factory air filter ever again as required maintenance. more
10/14/2017 8:42:28 AM
Airaid Jr Upgrade Kit for Factory Cold Air Intake Installation - 2016 Ram 2500- Video
Today on our 2016 Ram 2500, we'll be installing the Airaid Jr. Upgrade Kit for Factory Cold Air Intake, part number AR301-786. The Airaid Jr. Air Intake system is a quick and easy install, which illuminates the restrictive parts of the factory air box system. It will help us gain fuel economy and help us gain a little bit more power. Not only will it help us increase fuel economy though, but it'll also save us money in the long run because we don't have to worry about replacing our factory air filter anymore. more
12/27/2016 2:48:47 PM
aFe Direct-fit Cold Air Intake System Installation - 2002 Toyota Tundra- Video
All right, today on this 2002 Toyota Tundra, we are going to install part number AFE54-12262. To start off our install, we are going ahead and get underneath the hood, and we will go ahead and remove the trim cover over the throttle body. Next, there is going to be a bolt we have to remove from the AC line clamp. We will save that for re-installation later.Next, we need to remove the mass air flow sensor. First, we will go ahead and disconnect the wire harness, and then we will unscrew the screws for the sensor. We will set them aside in a safe place for now. more
7/16/2014 8:39:10 AM
Airaid CAD Cold Air Intake System Installation - 2012 Jeep Grand Cherokee- Video
Today on this 2012 Jeep Grand Cherokee, we're going to install part number AR311-212. This is Airaid CAD Intake System with SynthaMax Filter. First thing we need to do, open up the hood and get to the engine compartment. When you remove the engine cover, this whole assembly simply just pops up. Just pull up from the bottom and gently pull up and it will pop loose. Next, we need to loosen the hose clamp on the air box side of the intake tube. Let's undo the clamp. more
2/17/2014 11:43:40 AM
AIRAID CAD Air Intake System Installation - 2006 Chrysler 300C- Video
Today is a 2006, Chrysler 300C. We're going to install part number Ar350-199 from AIRAID. To start off our install, we're going to go ahead and disconnect the negative cable from the battery located in the trunk. Next we need to loosen the hose clamp that holds the factory intake tube to the throttle body. Next, we'll go ahead and disconnect the breather hose from the factory air box lid. Then we'll go ahead and remove the lid to the air box. We'll pull both lock down tabs towards the front. more
10/24/2013 5:04:29 PM
AIRAID CAD Intake System Installation - 2003 Chrysler PT Cruiser- Video
Today, on our 2003 Chrysler PT Cruiser, we're going to install part number AR300-138 from Airaid. This is the Airaid Cad intake system with a sensiflow filter, stage one. To start off our install, we'll go ahead and disconnect the negative battery cable. Then we need to remove the factory air lid. To do this, we'll go ahead and loosen up the clamp on the factory intake tube at the box lid. Then we can go ahead and unclip the factory air box lid, and remove it from the vehicle. Now typically, there's two clips; on this particular vehicle, one of the clips is missing. more
10/10/2013 10:00:45 AM
AIRAID CAD Air Intake System Installation - 2006 Ford F-150- Video
Today on our 2006 Ford F150 we'll be installing the Airaid Intake System, part number 401-140-2. Now to begin our installation underneath the hood here we'll need to disconnect the mass airflow sensor. We'll do this by sliding the red tab back and then simply removing the connector. We'll also need to slide the intake tube here on the other side off by moving the green clip and then pulling it off.We'll also need to disconnect the wiring harness from the air box in these two locations. We'll now take a 10mm deep socket and remove the four tower bolts, two on each side and also the one bolt holding the factory intake tube to the mounting bracket here. At this point we can go ahead and remove the entire factory intake system. more
8/13/2013 10:19:58 AM
AFE Air Intake System Installation 2005 GMC Sierra- Video
Today on the 2005 GMC Sierra 1550 series, were going to be installing the AFE Intake Kit product number AFE51-10092. The kit includes the replacement air filter, the new intake tube, an intake adapter and two different couplers, hose clamps, the trim seal, and then the new intake housing. Once we've ensured all that's there, we can go ahead and start with our installation. The first thing we want to do before we start moving each stock intake system is to go ahead and remove the negative terminal from the battery. Well reinstall this once the new intake is in, that will allow the system to reset itself around the new intake system. Ok, moving on to the factory air intake, were going to first disconnect the mass air censor.There is actually a clip that's on here that we need to remove that first. more
10/11/2011 9:58:33 AM
aFe Direct-Fit Cold Air Intake System with Pro Dry S Filter Installation- Video
Today on this 2009 Chevrolet Silverado 1500 series with a 5.3 liter engine we will be installing the AFE air intake system, part number AFE51-11752. The first thing we are going to do is remove the engine cover. It pops right off since it is a press fit. Next, we are going to loosen the clamp here that is attaching the tube to the intake housing and throttle body. We will do the same thing on the clamp on the other side. Next we are going to move over and disconnect the wiring harness from the sensor. Then we are going to remove the plastic line coolant brace from the intake tube. You can see this is a push rivet type connector. I an going to use a rivet removal tool, if you do not have one of these you can use a flat head screwdriver. Just slide it in there and separate the two. 1:00 more
4/19/2011 4:42:06 PM
